| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| fabwiki:research:usa:usa_schmitz [2023/10/19 11:36] – [INTRODUCTION] rpschmitz | fabwiki:research:usa:usa_schmitz [2023/10/19 11:38] (current) – [External Links] rpschmitz |
|---|
| <fs medium>The results of a plain concrete analysis for the panel under consideration show that a minimum panel thickness of 3½-inches is adequate. Figure 21 shows one possible reinforcement arrangement should some or all the variables noted above be exhausted and the only way to achieve an adequate panel design is to reinforce it. The reinforcement is placed where the principal tensile stresses are greatest.</fs> | <fs medium>The results of a plain concrete analysis for the panel under consideration show that a minimum panel thickness of 3½-inches is adequate. Figure 21 shows one possible reinforcement arrangement should some or all the variables noted above be exhausted and the only way to achieve an adequate panel design is to reinforce it. The reinforcement is placed where the principal tensile stresses are greatest.</fs> |
| ### | ### |
| | ~~UP~~ |
| ===== CONCLUSIONS AND RECOMMENDATIONS ===== | ===== CONCLUSIONS AND RECOMMENDATIONS ===== |
| |
| <fs medium>The author wishes to express his sincere appreciation to Professor Peter Huttelmaier, Ph.D. who served as Capstone Project advisor during graduate studies at the Milwaukee School of Engineering and offered insightful and constructive comments during the preparation of this manuscript. In addition, special thanks go to Professor Mark West, Director of the C.A.S.T. at the University of Manitoba, whose work on fabric-cast concrete wall panels provided the inspiration for this project. The author also wishes to thank Geri Schmitz and Gary Shimek, MLIS for their efforts in proofing this manuscript.</fs> | <fs medium>The author wishes to express his sincere appreciation to Professor Peter Huttelmaier, Ph.D. who served as Capstone Project advisor during graduate studies at the Milwaukee School of Engineering and offered insightful and constructive comments during the preparation of this manuscript. In addition, special thanks go to Professor Mark West, Director of the C.A.S.T. at the University of Manitoba, whose work on fabric-cast concrete wall panels provided the inspiration for this project. The author also wishes to thank Geri Schmitz and Gary Shimek, MLIS for their efforts in proofing this manuscript.</fs> |
| ### | ### |
| | ~~UP~~ |
| ===== See Also ===== | ===== See Also ===== |
| |
| <fs medium>//Place text here.//</fs> | <fs medium>//Place text here.//</fs> |
| | ~~UP~~ |
| ===== References ===== | ===== References ===== |
| |
| [11] Terram Ltd., May 2000, “Designing for Soil Reinforcement (Steep Slopes),” Handbook, (United Kingdom: Terram Ltd.), pp. 19-22. [Internet, WWW]. //Address//: http://www.terram.co.uk\\ | [11] Terram Ltd., May 2000, “Designing for Soil Reinforcement (Steep Slopes),” Handbook, (United Kingdom: Terram Ltd.), pp. 19-22. [Internet, WWW]. //Address//: http://www.terram.co.uk\\ |
| [12] ACI Committee 318. 2002. Building Code Requirements for Structural Concrete (ACI 318 02) and Commentary (ACI 318R-02). Farmington Hills, Michigan: American Concrete Institute.</fs>\\ | [12] ACI Committee 318. 2002. Building Code Requirements for Structural Concrete (ACI 318 02) and Commentary (ACI 318R-02). Farmington Hills, Michigan: American Concrete Institute.</fs>\\ |
| | ~~UP~~ |
| |
| ===== External Links ===== | ===== External Links ===== |
| <fs medium>[[http://www.umanitoba.ca/cast_building/|The Centre for Architectural Structures and Technology (C.A.S.T.)]]</fs>\\ | <fs medium>[[http://www.umanitoba.ca/cast_building/|The Centre for Architectural Structures and Technology (C.A.S.T.)]]</fs>\\ |
| <fs medium>[[http://www.fabric-formedconcrete.com/|Fabric-Formed Concrete]]</fs> | <fs medium>[[http://www.fabric-formedconcrete.com/|Fabric-Formed Concrete]]</fs> |
| | ~~UP~~ |
